Brick pointing and repointing
Pointing means cutting the failed mortar out of the joints between your bricks and filling them with fresh mortar. It is not decoration. The joints are what keeps rain out of a brick wall, and when they go soft or crumble, the wall starts drinking water. Done in time it is a maintenance job. Left too long it becomes brick replacement, and then wall rebuilding.
- NYC DCWP licensed
- Mortar matched to your wall
- Free written estimate
Call (929) 412-6597 Send photos of the wall
How to tell your joints have gone
- Mortar you can rake out with a key or a screwdriver, or that falls as sand at the base of the wall.
- Joints that have receded, so the bricks stand proud and the shadow lines look deep.
- Damp patches inside after rain, usually on the weather side or the rear wall, often at the top floor first.
- White powdery staining on the brick. That is efflorescence: salts carried out of the wall by water that is getting in and drying out again.
- Brick faces flaking or popping off. That is spalling, and it means water has been getting in and freezing. At this point pointing alone is no longer the whole job.
- Plants or moss growing out of the joints.
The mortar matters more than the labour
This is the part most owners are never told, and it is the difference between a wall that is fine for thirty years and a wall that is worse than before.
Mortar is supposed to be the weakest part of the wall. Buildings move with heat, cold and settlement, and that movement has to go somewhere. In a correctly built wall it goes into the mortar, which is why old joints crack and crumble while the bricks stay whole. Mortar is the sacrificial layer, and it is cheap to replace.
Now put hard modern Portland cement into an old wall of soft brick or brownstone. The mortar is suddenly stronger than the brick around it, so the movement has nowhere else to go, and the brick takes the strain instead. The faces blow off. Instead of repointing joints you are replacing units, on a wall that was fine until somebody “fixed” it. On a pre-war building this mistake can be worse than leaving the joints alone.
So we look at what the wall is made of before we mix anything. Soft old brick and brownstone want a lime-based mortar. Harder modern brick takes a cement mortar. We also match the colour and the joint profile, because a repointed patch in the wrong grey across a front elevation is permanent and very visible.
How we do it
- Look at the whole elevation, not only the patch you called about, and work out whether the joints are the actual problem or a symptom of something else.
- Rake the failed joints out to a proper depth. Shallow smearing over soft mortar is the most common bad job in this trade: it looks right for one season, then falls out.
- Brush and wet the joints so the new mortar bonds instead of drying out too fast against thirsty brick.
- Fill the joints in layers and tool them to match the profile of the original work.
- Brush the faces down and clean the site, including the sidewalk and whatever is below the work.
When pointing is not enough
An honest quote sometimes says the pointing is not the main job, and we would rather say so at the estimate than halfway through.
- Damaged or spalled bricks. Individual units can be cut out and replaced while the wall is open, matched as closely as the brick allows. It costs less to do this with the pointing than to come back for it later.
- A crack that splits the brick units themselves instead of following the mortar. That pattern means the wall is moving, not simply weathering, and an engineer should look at it before any mason prices repairs.
- Stepped cracks above a window. Usually the steel lintel underneath has rusted and expanded, lifting the brick above it. Pointing over that opens up again within a year. See lintel replacement.
- Water still coming in after good pointing. Then it is arriving another way: a parapet, a coping stone, flashing, or a wall saturated enough to need a coating. See exterior wall waterproofing.
Why quotes for the same wall differ so much
Owners regularly collect three bids for one elevation and get numbers that are nowhere near each other. It is almost never greed. It is that the three contractors priced different work: one quoted spot pointing of the worst joints, one quoted the full elevation, one included a scaffold where a lift would do, and one allowed for replacing twenty bricks that another ignored.
That is why our estimate is itemised. You can see the access method, the area, whether brick replacement is in or out, and what happens if we open the wall and find more. If you have a quote from somebody else, the fastest way to judge it is to put the two line by line against each other, and we are happy to do that with you.
What changes the price
The main things are the area of wall, how we reach it, and what the mortar has to be.
- Access. A ground-floor rear wall off a ladder is one price. Four storeys needing a boom lift or pipe staging is another, and the access can cost more than the pointing.
- Spot pointing or the whole elevation. Patching only the worst areas is cheaper today and usually means coming back; a full elevation costs more and ends the problem.
- Mortar type. A matched lime mix for a historic wall costs more than a standard mix.
- Brick replacement found once the joints are open.
- Landmark district. Approval and a mortar sample take time before anyone starts.
[OWNER TO CONFIRM: masonry warranty]
Landmarked buildings
If the building is in a historic district, repointing normally needs Landmarks Preservation Commission approval before work begins, and the Commission may want to see a mortar sample matching the original in colour, texture and strength. It is not usually difficult, but it has to happen before the scaffold goes up, not after a neighbour makes a phone call.
Where we do this work
The Bronx, Queens, Brooklyn and Manhattan. Most of it is on attached and semi-detached brick houses, two- and three-family buildings, brownstone and limestone fronts, and pre-war walk-ups.
Questions we get asked about pointing
How often does brick need repointing
There is no interval to put in a diary. A sheltered rear wall in good mortar can go fifty years or more; a south-west facing parapet that takes wind-driven rain and full freeze-thaw can need attention in fifteen. What decides it is exposure, the original mortar, and whether anything above the wall has been dumping water down it. The useful test is physical, not calendar-based: if a key scrapes the joint away as sand, it is time.
Can you point only the bad patches
Yes, and sometimes it is the sensible choice, particularly on a large building where one corner has failed. Be clear about the trade-off though. Spot pointing fixes the area that failed first, and the areas that are halfway there will keep going. A patched elevation in slightly different mortar also shows. If most of a wall is soft, doing it once costs less than doing it in three visits.
Will the new mortar match the old
We mix to match colour, texture and joint profile, and it is usually close. It will not be invisible on day one: fresh mortar is lighter than mortar that has been weathering for decades, and it darkens over the first year or two. Anybody promising an exact match on a hundred-year-old wall is overselling.
Does pointing stop a leak on its own
Often, because failed joints are the most common way water crosses a brick wall. Not always. If the water is arriving over the top of a parapet, through a split coping joint, behind failed flashing or around a window frame, new joints will not stop it. That is why we look at the whole elevation before quoting rather than pricing the patch you pointed at.
How long does the work take
A single rear elevation on a small house is usually a matter of days. A full street frontage with lift access runs longer, and the access equipment often dictates the schedule more than the pointing does. Weather matters too: mortar needs reasonable temperatures to cure, so a hard freeze stops work rather than slowing it.
Can pointing be done in winter
Up to a point. Mortar will not cure properly below roughly freezing, and work done in the cold without protection fails early. We would rather tell you to wait a fortnight than take your money for mortar that will not set. The exception is where a violation or an inspection report is running against a deadline, and then it becomes a question of protection and planning the work in the warmer part of the day.
Get it looked at
Send photographs of the wall, ideally one from across the street and one close enough to see the joints. We can usually tell from those whether you are looking at pointing, brick replacement, or something behind the wall.
Call (929) 412-6597 Get a written estimate
More masonry work is on the masonry page. Our licence number and insurance are on the credentials page.