Chimney repair and rebuilding
A chimney is the hardest-working masonry on a building. It stands clear of everything else, so it takes weather on all four sides and from above, and it has no heated structure below to keep it dry. That is why chimneys fail first, often by a decade, while the wall beneath them is still sound.
This is masonry work: pointing, crowns, caps, flashing details at the roof line, and rebuilding. It is not chimney sweeping.
- NYC DCWP licensed
- Brick, crown and cap work
- Free written estimate
Call (929) 412-6597 Send photos of the chimney
Signs a chimney needs work
- Missing mortar between the bricks, visible as dark gaps from the ground or in a photograph taken with a zoom.
- Brick faces flaking or crumbling. Spalling happens faster on a chimney than anywhere else on the building.
- A cracked or missing crown, the sloped concrete cap on top. Water that gets past the crown runs down inside the brickwork where you cannot see it.
- A visible lean, or courses that no longer line up.
- Damp or staining on the ceiling or wall of the top floor near where the chimney passes through.
- White salt staining on the brick, which means water is moving through it.
- Pieces of brick or mortar on the roof or in the gutter.
Why water gets in at the top first
Most chimney problems start with the crown. It is a slab of concrete or mortar on top of the stack, sloped so rain runs off and overhangs slightly so the water drips clear of the brick. When it cracks, water goes straight down inside the masonry instead.
From there it behaves the way water always does in a wall: it soaks in, freezes, expands and opens the joints a little more each winter. A chimney goes through more of those cycles than any other part of the building, so the damage accelerates. By the time bricks are loose at the top, the crown has usually been broken for years.
What we do
- Repointing the stack, in mortar matched to the brick, which on an older chimney means not using a hard modern cement that would damage soft brick.
- Crown repair or rebuilding, with the slope and the overhang formed properly so water leaves the stack instead of running into it.
- Brick replacement where faces have spalled or units have come loose.
- Partial rebuild, taking the stack down to sound masonry and rebuilding from there. This is the common repair on a chimney where the top few feet have gone.
- Full rebuild where the stack is leaning, the mortar has gone throughout, or the brick is beyond saving.
- Caps to keep rain, birds and debris out of the flue.
- Waterproofing of the stack where the brick has become porous.
- Demolition and capping off, where a chimney is disused and the owner would rather remove the liability than maintain it.
Repointing or rebuilding
The test is whether the stack is still structurally sound. If the bricks are solid and only the joints have failed, repointing with a new crown is the right job and the cheaper one. If bricks are loose, tilting or missing, or the stack is out of plumb, no amount of pointing will hold it together and a rebuild is what is actually needed.
Rebuilding only the top portion is very often enough, because the damage concentrates above the roof line where the exposure is. We will tell you where sound masonry starts.
Where the chimney meets the roof
A large share of “chimney leaks” are not the chimney at all: they are the flashing where the stack passes through the roof. The masonry can be perfect and water will still come in if that detail has failed.
That is a roofing detail rather than a masonry one. We are the same company as manhattanroofing.nyc, so it can be looked at on the same visit rather than turning into two contractors blaming each other. What we will not do is repoint a stack and leave, knowing the leak was the flashing.
What we do not do
We are masons. We do not sweep chimneys, inspect flues with a camera, or install liners. If you are burning anything in the fireplace, those are real safety jobs and they belong to a chimney sweep or a licensed specialist, not to us. Plenty of firms advertise both; we would rather be clear about which one we are.
What changes the price
- Access. Everything happens at roof level, so getting equipment and people up there is a real part of the cost.
- Repoint, partial rebuild or full rebuild, which is decided by the condition rather than the budget.
- Height of the stack above the roof line.
- Matching brick on an older chimney.
- Whether the crown and flashing are being done at the same time, which they usually should be.
[OWNER TO CONFIRM: masonry warranty]
Questions about chimney work
My chimney is not used, can I ignore it
An unused chimney still has to stay up. It is masonry several feet above a roof, and if it comes apart the pieces land on your roof, your neighbour’s, or the sidewalk. A disused stack also keeps letting water into the building. The two sensible options are a proper repair with a cap, or taking it down to roof level and closing it off. Either costs less than leaving it to come apart on its own schedule.
How long does a chimney rebuild take
A crown and a repoint is usually a short job. A top rebuild of a few feet is typically a day or two of masonry once access is set up. Access and weather usually decide the programme more than the brickwork does, and mortar will not cure properly in a hard freeze.
Can you match the old brick
Usually close, rarely exact. Brick colour and texture varied by kiln and by decade, and a century of weathering cannot be bought off a pallet. On a visible front elevation it is worth discussing before the work; on a rear stack most owners would rather have it sound than perfectly matched.
Where we do this work
The Bronx, Queens, Brooklyn and Manhattan.
Get the chimney looked at
A zoomed photograph from the street or from a neighbouring window tells us a surprising amount. Call (929) 412-6597 or use the estimate form. Pointing on the rest of the building is on the brick pointing page.