Water coming through an exterior wall
A brick wall is not waterproof, and it was never built to be. It is meant to absorb a certain amount of rain and then dry out again before the next storm. Trouble starts when more water gets in than can leave: the joints have gone soft, the brick has become porous, or something above is pouring water down the face faster than it can shed.
- NYC DCWP licensed
- Cause first, product second
- Free written estimate
Call (929) 412-6597 Send photos inside and out
What you are probably seeing
- A damp patch inside that darkens after rain and fades between storms.
- Paint or plaster bubbling, blistering or lifting off an outside wall.
- White powdery deposits on brick or on the inside face. That is efflorescence: salt left behind by water moving through the masonry and evaporating.
- A musty smell in a room that backs onto an exterior wall.
- Mould in one corner, typically where two exterior walls meet and the structure stays coldest.
- Brick faces flaking outside, which is the same water freezing in the wall.
- Dark staining running down the outside below a sill, a coping or a downspout joint.
Reading the pattern before touching anything
Where and when the damp appears narrows the cause down more reliably than any gadget.
| What you see | What it usually means |
|---|---|
| Damp only during and just after driving rain | Water crossing the wall face or an opening on the weather side |
| Damp high up, top floor, after rain | Parapet, coping joints or the top of the wall |
| A horizontal band at one level | Something at that line: a shelf angle, a flashing, a change in the wall |
| Around a window only | Sealant, the sill slope, or the lintel above |
| Low on the wall, present all year | Ground water, splash-back or the grade sitting too high against the building |
| Unchanged by weather | Likely plumbing rather than rain, and worth ruling out before masonry work |
What the repair usually is
On most New York brick buildings the honest answer is masonry, not a product. Repointing an elevation in a mortar matched to the brick restores the barrier that was there originally, and on a wall whose joints have failed it is the whole fix. That work is described on the brick pointing page.
Depending on what we find, the work can also include:
- Replacing spalled or cracked brick that is drawing water in.
- Repairing or resetting coping stones and sealing the joints between them.
- Re-forming a sill so it sheds water, and reopening a drip edge that was caulked shut.
- Renewing failed sealant around window and door openings.
- Redirecting a downspout that has been discharging onto the wall.
- Applying a breathable water repellent or coating, once the wall is sound and dry. See masonry coatings.
The sealing trap
It is tempting to coat the whole wall and be done. On a wall whose joints have failed, that is the wrong order, and often the wrong job entirely.
A coating over soft mortar hides the problem without stopping it; the joints keep deteriorating underneath. Worse, an impermeable coating slows the wall drying out. Water still finds a way in at the one place that was not sealed, and now it cannot leave. It sits in the masonry, freezes, and takes brick faces off from behind. The wall ends up worse than if nobody had touched it.
So: repair first, make sure the wall is dry, then coat only if coating is actually needed. Any contractor who quotes a sealant for a leaking brick wall without looking at the joints is selling the easy half of the job.
Balconies and terraces
A balcony or terrace is a flat surface attached to a wall, so it concentrates water exactly where the building is most vulnerable: at the junction. Failed surface waterproofing, a blocked drain or a threshold detail that was never right will push water into the wall and into the room below. These are worth looking at as a wall problem and a surface problem together, not one or the other.
What changes the price
- Area of wall and how much of it needs work.
- Access, which on anything above the second floor is a real cost of its own.
- Pointing versus brick replacement, decided once the joints are open.
- Whether the source is at roof level, which adds parapet or coping work.
- Coating or not, and which type the wall actually needs.
[OWNER TO CONFIRM: masonry warranty]
Questions about wall leaks
Can you stop it from inside
Sealing the inside face can hide a stain, and in a basement a tanking system is a legitimate approach. On an above-ground wall it is usually a bad trade: the water still arrives, it just collects in the masonry behind your new finish, and it will push that finish off and keep damaging the wall. Stopping water on the side it arrives from is almost always the better answer.
How long before the wall dries out
Longer than people expect. A wall that has been soaking for years holds a lot of water, and after the repair it can take months of normal weather to give it up. Stains inside may need redecorating once, after the wall has dried, rather than immediately.
Is efflorescence a problem in itself
The white deposit is harmless; it is just salt. What matters is what it tells you, which is that water is moving through the masonry and evaporating at the surface. Brushing it off without addressing the water means it comes back.
Where we do this work
The Bronx, Queens, Brooklyn and Manhattan.
Start with photographs
Send the damp inside and the outside wall in the same area, and tell us whether it tracks the rain. That is usually enough to say what we would be looking at. Call (929) 412-6597 or use the estimate form.